Delta dtc 1000 manual10/30/2022 ![]() ![]() If you require dual loop output, the 2 outputs should be set to different actions (heating or cooling). #Delta dtc 1000 manual seriesThere are several output types available from DTC1000/2000 series: Control Output (heating/cooling), Alarm Output and Proportional Output.ĭTC1000/2000 series offers 2 outputs for heating or cooling control. If we change the range to 0 ~ 2,000, 0 will refer to 0mA input, and 2,000 will refer to 20mA input. Take 0 ~ 20mA input as example, -999 refers to 0mA input, and 9,999 refers to 20mA input. The range of linear input and feedback value is adjustable. See “How To Set up Current Input” section. Note 1: The current input is built-in with 249Ω precision resistor. 300m/s 2, 3 times in each 3 axes, 6 directionsĭTC1000/2000 series supports the following input sensors: Internal terminals available to transmit 24V power supply and communication signalsġ0 ~ 55Hz, 10m/s 2 for 10mins, each in X, Y and Z direction Proportional output is available only when output 1 is linear voltage/current output. ![]() output current: 40mAĬurrent: DC 4 ~ 20mA (Load resistance: 1,000Ω)Ĭontrol output, alarm output, proportional output Thermocouple: K, J, T, E, N, R, S, B, L, U, TXK 24 W combined, 3W + 3W x number of DTC2000 controllers (Max. Not available now.Įnclosed functions: DC24V input, 2 outputs, relay output for output 2, RS-485 communication. Not available now.Ģ: 2 auxiliary outputs. Please keep proper space in between.ĭTC: Delta C series temperature controllerĠ: standard, 2 outputs, no auxiliary outputġ: 1 auxiliary output. power supply) in parallel with DTC1000/2000 during the installation. DO NOT touch the internal terminals no matter the power is on or off.ġ0. DO NOT touch any internal circuit within this period.ĩ. Wait at least one minute after the power is off to allow the capacitor to discharge. DO NOT touch the terminals or repair the controller when the power is on to prevent electric shock.Ĩ. Make sure the power cable and signals device are installed correctly before switching on the power of DTC1000/2000 otherwise serious damage may occur.ħ. Shorten the wire when wiring a platinum resistance thermometer (RTD) to the controller, and separate power cable from load wires to prevent interference and conductive influence.Ħ. ![]() Be sure to use compensating wires that match the thermocouple types when extending or connecting the thermocouple wires.ĥ. Switch off the power when wiring or changing input sensors.Ĥ. #Delta dtc 1000 manual installDo not install and/or use the controller in places subject to:ĭust or corrosive gases and liquid high humidity and high radiation vibration and shockģ. DO NOT modify or disassemble the controller. Prevent dust or metallic debris from falling into the controller that will cause malfunction. key or specific tools are required to open the enclosure) in case danger and damage on the device may occur.ġ. The enclosure should prevent non-maintenance staff from operating the device (e.g. #Delta dtc 1000 manual freePlease read this instruction sheet before using your DTC1000/2000 series to ensure proper operation, and please keep this instruction sheet handy for quick reference.ĭTC1000/2000 series is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. ![]() Thank you very much for purchasing DELTA DTC1000/2000 Series Temperature Controller.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |